For over 50 years

Granberg International has manufactured quality chainsaw accessories.

How To Make Lumber With The Alaskan Chainsaw Mill MKIII

rail-1 rail-2 rail-3 rail-4
rail-1 rail-2 rail-3 rail-4

How to set up and cut a log into slabs using the G850 Slabbing rail brackets with 2 x 4 guides and the G776-24 Alaskan Saw Chainsaw Mill.


Equipment Needed Set Rails on Top of Log Adjust Cutting Depth First Cut on Rails
2nd Cut on Previous Surface End of Second Cut Another Cut Stack, Stick & Dry

The Alaskan Small Log Chainsaw Mill and Mini Chainsaw Mill in Use.
How to Cut a log that is longer than the G555b set up board.

Picture 1 Picture 2 Picture 3 Picture 4 Picture 5 Picture 6 Picture 7 Picture 8 Picture 9 Picture 10 Picture 11 Picture 12 Picture 13 Picture 14 Picture 15 Picture 16 Picture 17 Picture 18 Picture 19 Picture 20 Picture 21 Picture 22 Picture 23 Picture 24 Picture 25 Picture 26 Picture 27 Picture 28 Picture 29 Picture 29A Picture 30 Picture 31 Picture 32 Picture 33 Picture 33A Picture 34 Picture 35 Picture 36 Picture 37 Picture 40 Picture 41 Picture 42 Picture 43 Picture 43A Picture 44 Picture 45 Picture 46 Picture 47 Picture 48 Picture 49 Picture 50 Picture 51 Picture 52 Picture 53 Picture 54 Picture 54A Picture 54B Picture 55 Picture 56 Picture 57 Picture 58 Picture 59 Picture 60 Picture 61 Picture 62 Picture 63 Picture 64 Picture 65 Picture 66 Picture 67

Granberg International president Erik Granberg milling some urban timber into lumber with the Alaskan Small Log Chainsaw Mill.


Erik_1 Erik_2 Erik_3 Erik_4
Erik_5 Erik_6 Erik_7 Erik_8
Erik_9 Erik_10 Erik_11 Erik_12
Erik_13 Erik_14 Erik_15 Erik_16

Mike Wood of Talkeetna Alaska lives five miles out of town on the Susitna River. Using the Alaskan Chainsaw Mill and his canoe, he was able to cut and transport all the timbers and lumber needed to build his cabin.

Milling 2 x 14 foot floor boards Using his 21 foot canoe Mike transported 12 to 14 2 x 10’s across the river to his homesite on the other side The floor framing and wall timbers Notching the timbers Tongue and groove floor framing
Assembling the timber wall frame The timber frame with roof timbers Almost finished Ready for winter

Cutting Hawaiian hardwood with the Alaskan Chainsaw Mill by Darryl Fritz, a contractor located on Maui.

Using a simple 2 x 4 set up for the first cut guide Keeping the mill tracking on the guide A perfectly flat first cut Cutting the second slab
Cutting the second slab Beautiful grain A truck load of valuable hardwood in just a few hours

After drying, Darryl used one slab to make a beautiful Tiki Bar. A unique project made possible with the Alaskan Saw Chainsaw Mill.

1tikbarpics 2tikbarpics 3tikbarpics 4tikbarpics

Tables made by Glenn Holsworth cut with the Alaskan Saw Chainsaw Mill in Northern California.

Walnut side table with maple trim Large dining table from California claro walnut Maple coffee table with four seperate sections

Milling long timbers with the Alaskan Chainsaw Mill has always involved a more complicated first cut set up due to the longer lengths. With the recent availability of laser levels and the EZ Rail guide system, this has been simplified. Our EZ rail kits come in 5 foot and 9 foot sections. This procedure can be done using any combination of different EZ rail lengths.

Picture1 Picture2 Picture3 Picutre4
Picture5 Picture6 Picture7 Picture8
Picture9 Picture10 Picture11 Picture12
Picture13 Picture14 Picture15 Picture16

Top of Page